Career Episode 1 Assignment Help

CE1.1) Introduction

Career Episode 1 Assignment HelpThe episode demonstrates how I practiced my telecommunication engineering skills throughout an individual project titled “FM Receiver Design” at COMSATS Institute of Information Technology (CIIT), Islamabad, Pakistan. I commenced this project in July 2011 and submitted the final report in November of that year. Also view Engineering Assignment Help

CE1.2) Background

The most crucial engineering subject for telecommunication engineering student at CIIT was Telecommunication Systems Engineering which revolved around the premise of most important and basic communication systems. This subject was integrated with laboratory experiments. And students were obligated to work on the design of a Frequency Modulation (FM) receiver to successfully complete the course.

In this project I aimed for:

  1. Developing my knowledge in regard with telecommunication engineering principles
  1. Applying electronic principles to implement my ideas
  1. Analysis of designed FM receiver performance

For having this project accomplished, I communicated effectively with lab demonstrators when encountered challenges and used their assistance in programming PSpice software and circuit fabrication. View more at Mechanical Engineering Assignment Help

CE1.3) Activities Regarding Personal Engineering

CE1.3.1) Requirement of FM Receiver

Since an important part of the lecture time was allocated to FM technology and design of Receivers. I used lecture notes and text books to study the nature of FM technique and their applications, Modulators and Demodulators, Amplitude & Phase Modulation methods, Frequency Spectrum Sharing and Filtering principles. The first step of the project was to theoretically analyse the behaviour of an FM receiver. Therefore in order to do so I considered a scenario that the FM receiver is a radio which should be able to receive any type of audio sources simultaneously. In Pakistan, the radio stations are designated with a specific carrier frequency and they share the frequency spectrum over the air through AM and FM modulation.

Considering the above facts, I used Fourier mathematical rules to design different signals spectrum. And applied Frequency Division Multiplexing (FDM) technique to create a carrier which can transmit both FM and AM signals simultaneously. I came to this understanding that I require to amplify the received signal. Filter out all noises and interfering signals from other stations, and a demodulator to build my receiver. Order Now

CE1.3.2) FM Receiver Design

Using the results of my research and following the instruction of the lab demonstrators, I applied Phase Lock Loop (PLL) technique to design my receiver.

  1. Phase Detector (PD): I employed this device to produce a voltage signal to distinguish the difference in phase between two signal inputs
  1. Filter: I considered the design of a filter to eliminate undesirable frequencies components which pass the phase detector
  1. Oscillator: By using this device I created a synchronous representation of sinusoidal waveforms

Although from this stage on I had to come up with novel ideas to link electronic principles to turn my ideas into reality. Therefore I used this multiplexer as a representation of PD. I did mathematical analysis on the role of PD by investigating the spectrum of multiple signals. Used PSpice software and used these signals as input to my designated multiplexer. And studied its performance on detecting phase difference and DC shift.

The next step of the design was creating a low pass filter which could eliminate unwanted signals from the carrier. Therefore, any signal that is received on the antenna that is not in this range should be rejected. In order to do so, I mathematically modelled the low pass filter using Laplace transfer functions.

Assignment Help UK

Then, I had to create an electronic circuit for the filter, using resistors and capacitors. I calculated the value of these devices by considering the desired cut-off frequency and required bandwidth values and employing proper equations which linked these parameters to each other. Since I used PSpice to simulate my circuit and fed different carrier signals through. And tested the performance of the filter by generating diagrams which showed the frequency and amplitude response of the filter against different frequencies.

Moreover, using this simulation software. I could try different topologies for the filter circuit. And changed the value of capacitors and resistors to achieve an optimum performance. Afterwards, I connected the multiplexer to an oscillator to produce frequency signals resembling FM radio frequencies.

However, during laboratory practices I faced a technical challenge which led to poor signal recovery. Resolve this issue with high frequency amplifiers. I designed my amplifier to operate with 60 Ohm impedance, functional frequency of 50 and 500 MHz, and 14dB of gain at 150MHz.

Moreover, I improved the quality of the recovered signal by using an Anti-Aliasing filter to work as a restriction towards the bandwidth of signal to satisfy the sampling theorem. Firstly I applied Nyquist theorem to discover the best sampling rates. Therefore and then I applied this filter by employing a 3 pole Sallen Key Butterworth active low pass filter. I calculated the nodal equations and the transfer function of the circuit. And have the values of resistors and capacitors for a 10Hz cut-off frequency calculated. Upload your assignment now and get exciting offers.

CE1.3.3) Circuit Assembly

After having the different parts of the system simulated in PSpsice and ensuring that they operate within the proper range and band width, I gathered the necessary electronic component that I used in my design along with a Printed Circuit Board (PCB). However I used soldering techniques to install each device on the board. I also installed a 70 Ohm FM antenna. After I connected the audio amplifier and a speaker, I was able to detect 88.5, 89.3, and 91.3MHz. I also used a strong university antenna to see if my receiver could pick other stations.

CE1.4) Summary

This laboratory assignment was a very interesting opportunity to introduce me to the field of telecommunication systems. I applied a significant level of mathematical knowledge to analyse the role of electronic devices in filters, detectors, modulators, etc. Moreover, I was able to practice manual skills in assembling a telecommunication device which could actually detect signals and demodulate them. The final report and receiver was submitted to lab demonstrators and I was able to accomplish all the requirement of this project.

1 Step 1
GET INSTANT ASSIGNMENT HELP BY PHD EXPERTS FROM UNITED KINGDOM
keyboard_arrow_leftPrevious
Nextkeyboard_arrow_right